The article at PA0FRI's website has some photos of the loop being laid out along a chalked line on a piece of plywood. The results appear pretty good.
http://www.pa0fri.com/
Search found 318 matches
- Tue Oct 02, 2018 7:56 pm
- Forum: SDR Antennas
- Topic: Loop Construction
- Replies: 9
- Views: 35342
Re: Carriers
Paul
In the simplest terms: Your receiver provides the carrier. See 'Beat Frequency Oscillator' at Wikipedia
In the simplest terms: Your receiver provides the carrier. See 'Beat Frequency Oscillator' at Wikipedia
- Fri Sep 21, 2018 2:11 pm
- Forum: General
- Topic: 137100000 or 137900000 for Meteor M2
- Replies: 1
- Views: 6138
- Fri Sep 21, 2018 2:09 pm
- Forum: New Users' experiences
- Topic: Can I get Meteor m2 with RSP1a and SDRuno
- Replies: 7
- Views: 32434
Re: Can I get Meteor m2 with RSP1a and SDRuno
To answer your last question first. I believe that Sharp receives it's tracking data over a DDE link while SDRUno receives it over a virtual comm port. I haven't used SDRUno with Orbitron recently, but as I recall WispDDE must be set up to emulate a TS-2000 radio to communicate with SDRUno over a vi...
- Wed Sep 19, 2018 12:33 pm
- Forum: SDR Antennas
- Topic: Wellbrook ALA1530LN
- Replies: 5
- Views: 18455
Re: Wellbrook ALA1530LN
Thanks Paul
I thought perhaps it was an electronic fuse. I have one of these on a supply for a Mini Whip. In order to reset it after an overload, I must power it down and turn it back on.
I thought perhaps it was an electronic fuse. I have one of these on a supply for a Mini Whip. In order to reset it after an overload, I must power it down and turn it back on.
- Wed Sep 19, 2018 11:09 am
- Forum: New Users' experiences
- Topic: Can I get Meteor m2 with RSP1a and SDRuno
- Replies: 7
- Views: 32434
Re: Can I get Meteor m2 with RSP1a and SDRuno
You need an old version of SDRSharp, version 1361 or earlier, the newer versions will not support the ExtIO plugin which is available here in the downloads section of this site. Also the demod and tracker plugin you need must be the DotNet 3.5 version. The old SDRSharp 1361 is here: https://www.qsl....
- Wed Sep 19, 2018 9:44 am
- Forum: SDR Antennas
- Topic: Wellbrook ALA1530LN
- Replies: 5
- Views: 18455
Re: Wellbrook ALA1530LN
Paul: What is the procedure for resetting the built-in fuse? Or, does it require replacement if it trips?
- Wed Sep 19, 2018 9:27 am
- Forum: New Users' experiences
- Topic: Can I get Meteor m2 with RSP1a and SDRuno
- Replies: 7
- Views: 32434
Re: Can I get Meteor m2 with RSP1a and SDRuno
2018-9-12-9-24-23-790_122.RGB122 copy.jpg Hurricane Florence from Meteor M2 using RSDRPlay RSP2, Homebuilt QFH Antenna, SDRSharp v1361 w/realtime Meteor QPSK plugin & DDE tracking plugin (for Doppler correction), and Orbitron for Sat tracking and doppler. The RSP2 works much better than a dongle. Y...
- Mon Sep 17, 2018 2:08 am
- Forum: SDRuno
- Topic: SDRuno Software Issue
- Replies: 6
- Views: 15822
Re: SDRuno Software Issue
In SDRUno 1.22/1.23:
In the RX Control Panel:
Right click inside the frequency display area.
The Tuning Step Popup will open.
Left click on the desired Step.
The current frequency step is displayed in the upper left corner of the frequency display window.
In the RX Control Panel:
Right click inside the frequency display area.
The Tuning Step Popup will open.
Left click on the desired Step.
The current frequency step is displayed in the upper left corner of the frequency display window.
- Mon Sep 10, 2018 12:20 am
- Forum: New Users' experiences
- Topic: Absolutely Green New User
- Replies: 5
- Views: 20085
Re: Absolutely Green New User
Are you sure of entering the correct frequency? An FM broadcast on say 105.5 FM will be entered in SDRUno as 105500000, 1220AM as 1220000. Also use the correct mode AM, FM etc and bandwidth for the signal you are hearing. You should be able to hear and see signals on the spectrum display on the AM o...