Search found 79 matches
- Mon Nov 27, 2017 8:37 am
- Forum: General
- Topic: the band is packed like sardines
- Replies: 1
- Views: 7066
Re: the band is packed like sardines
Not only the BC band was packed. This is the how the CW part of 20m band looked last weekend:
- Wed Nov 15, 2017 1:12 pm
- Forum: General
- Topic: GQRX crash, OSX, RSP2 and SoapySDR
- Replies: 3
- Views: 11056
Re: GQRX crash, OSX, RSP2 and SoapySDR
Yes it's a soapysdrplay or gr-osmosdr problem (Don't remember exactlly which one). It raises an exception if a function is not supported (instead of simply returning an error). I fixed it some time ago on my local build and thought it is now fixed upstream. Do you get this crash if you disable the i...
- Wed Jun 21, 2017 11:38 am
- Forum: SDRuno
- Topic: SDRuno - Rig Syncronization
- Replies: 7
- Views: 25009
Re: SDRuno - Rig Syncronization
This is a problem I encountered in my home made synchronization solution under Linux too. If there are modes that exist only on one of the rigs, there is a mapping needed in both directions. Unfortunately this mapping is not always 1:1, but can be 1:N. In my implementation I have some "heuristics" t...
- Tue Jun 06, 2017 7:49 am
- Forum: SDRplay related
- Topic: Ubuntu 16.04 current soapysdr and built sdrplay module fail.
- Replies: 5
- Views: 18991
Re: Ubuntu 16.04 current soapysdr and built sdrplay module fail.
GQRX isn't working, but I think I just have to build gr-osmosdr with the non-free switch to get there. This is not required if you are using the soapysdr bacckend in gromosdr. But I think you need quite recent grosmosdr and soapysdrplay for working with API 2.x and RSP2. (I have an RSP1 so I can't ...
- Tue Jun 06, 2017 7:35 am
- Forum: General
- Topic: MAC API Breaks GQRX
- Replies: 1
- Views: 6842
Re: MAC API Breaks GQRX
I am running Linux, but maybe its similar... grosmosdr by default has no support for the SDRPlay. You have 2 choices: 1. Build grosmosdr with non free drivers enabled 2. Install soapysdr/soapysdrplay (preferred method). I had to build it from source. You need quite recent versions of soapysdr and gr...
- Wed May 10, 2017 12:25 pm
- Forum: SDRplay related
- Topic: RSP1 with Yaesu FT-1000MP Mk V
- Replies: 1
- Views: 9419
Re: RSP1 with Yaesu FT-1000MP Mk V
Maybe you have to configure your FT-1000 to actually use the RX IN input? On my TS590SG, I have to do this, otherwise the TRX antenna (SO239 socket) is used. What happens if you connect your antenna to the SO239 socket? On the TS590SG, I have to enable the RX out function too, because using the RX o...
- Fri May 05, 2017 8:37 am
- Forum: SDRuno
- Topic: Audio latency and CW QSK
- Replies: 2
- Views: 9563
Re: Audio latency and CW QSK
Unfortunately if have no suggestion, but I am suffering from the same problem. How long is your delay/latency? I measured about 130ms from antenna input to audio output on a good day (it depends a bit how the audio output buffer size is adjusted) and that pretty much destroys any QSK. I am running L...
- Sun Feb 26, 2017 9:22 am
- Forum: General
- Topic: RSP2 and Linux
- Replies: 5
- Views: 16907
Re: RSP2 and Linux
I just noticed in the document that for CubicSDR I have to build wxwidgets from source. On Ubuntu 16.04 I just installed wxwidgets and wxwidgets devel packages and could build CubicSDR just fine and it seems to work without problems. Is there a problem with the standard wxwidgets that I just didn't ...
- Tue Feb 21, 2017 2:57 pm
- Forum: SDRplay related
- Topic: SDR play connected via IF out and transmit
- Replies: 6
- Views: 21009
Re: SDR play connected via IF out and transmit
I have my RSP1 connected to the RX antenna output of my TS590SG without any protection. No problems so far. I also tested with an active whip antenna connected directly to my RSP1. The whip delivers about 10 dBm when I transmit. This might be considered dangerous, but no problems so far. Transmit po...
- Sat Jan 28, 2017 7:12 pm
- Forum: New Users' experiences
- Topic: CubicSDR working fine, Gqrx not so good.
- Replies: 7
- Views: 25366
Re: CubicSDR working fine, Gqrx not so good.
Got soapy working with gqrx needed to change the driver string to 'driver=sdrplay,soapy=0' now to work out how to change the antenna. Seems to be unsupported: /******************************************************************* * Antenna API *********************************************************...