LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Useful information regarding antennas for SDR products.
glovisol
Posts: 662
Joined: Thu May 10, 2018 6:42 pm
Location: Piedmont, Italy

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by glovisol » Wed Jul 10, 2019 5:24 pm

Hi Paul,

Do not worry for the 80+, I will turn 80 in september next....so you are in good company.

Detailed instructions with pertinent photos are posted here:

https://www.sdrplay.com/community/viewt ... 9&start=20

Just patiently go over the thread until you come to the directions for building the transformer (very easy!)

Kind regards,

Gianfranco

Reason: No reason

Paul
Posts: 355
Joined: Fri Feb 17, 2017 9:52 am
Location: SW UK

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by Paul » Wed Jul 10, 2019 6:55 pm

Thanks again Gianfranco - Pictures ARE worth a 1,000 words!

Reason: No reason

glovisol
Posts: 662
Joined: Thu May 10, 2018 6:42 pm
Location: Piedmont, Italy

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by glovisol » Wed Jul 10, 2019 7:22 pm

Hi Paul, I wish to correct my statement on the abnormal difference in sensitivity between the HI Z and the 50 Ohm input. This has been caused by an unsuitable transformer used on the 50 Ohm input, because being far from home I have very limited resources here. I hope to get suitable 50 Ohm transformers soon. In any case this seems to point to the fact that the transformer termination of the antenna is extremely critical.

Apologies for this mistake.

Gianfranco

Reason: No reason

vk7jj
Posts: 206
Joined: Thu Mar 02, 2017 9:56 am
Location: Tasmania

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by vk7jj » Wed Jul 10, 2019 11:52 pm

Hi Gianfranco,

You asked me to model your pallet, here it is over real ground at a height of 16m:

Overview showing current flow (the blue lines) is equal in all four sides
Feedpoint is the red dot.
modelview.png
modelview.png (48.65 KiB) Viewed 1407 times
The pattern is omni with useful lowish angle lobes that are giving you all that nice activity
pattern.png
pattern.png (97.7 KiB) Viewed 1407 times
40m (7.15MHz) antenna characteristics
7MHz.png
7MHz.png (24.22 KiB) Viewed 1407 times
Forgive my screen pic dump quality; the Mac 4K screen dumps at 144dpi resolution and those images get resampled to presumably 72dpi and become annoyingly unsharp.

Thanks for the kind comments from you and sdrom33 but the truth is VK7JJ is just another flawed wannabe standing on the shoulders of giants like Cebik, waving a little flag and pointing to things he's borrowed from them; much better to go straight to the giants themselves.

Its really great to see you and Paul going at it!

Phil

Reason: No reason

vk7jj
Posts: 206
Joined: Thu Mar 02, 2017 9:56 am
Location: Tasmania

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by vk7jj » Thu Jul 11, 2019 12:05 am

Here it is again at 6m (51MHz) and UHF (432MHz) to show how a loop is good for wide band work.

You'll note the gain, something you will not get from a vertical whip or groundplane, along with the improved radiation resistance and reactance.

The angle of radiation is actually better than a vertical, vertical patterns break up into even higher angle lobes as you go up in frequency. The old ham chat about a kite with a kilometre long wire being the ultimate HF antenna - maybe so if it was caught in a tree about one kilometre away.
Screen Shot 2019-07-11 at 10.00.44 am.png
Screen Shot 2019-07-11 at 10.00.44 am.png (140.09 KiB) Viewed 1624 times
Screen Shot 2019-07-11 at 9.59.55 am.png
Screen Shot 2019-07-11 at 9.59.55 am.png (145.36 KiB) Viewed 1624 times
Phil

Reason: No reason

Paul
Posts: 355
Joined: Fri Feb 17, 2017 9:52 am
Location: SW UK

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by Paul » Thu Jul 11, 2019 4:58 am

Hi Gianfranco
Thanks for the update.

Reason: No reason

Paul
Posts: 355
Joined: Fri Feb 17, 2017 9:52 am
Location: SW UK

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by Paul » Thu Jul 11, 2019 5:12 am

Hi again Gianfranco
A further question if I may please:
Should this antenna work on a flat surface?
Pardon the obvious ignorance.

Reason: No reason

glovisol
Posts: 662
Joined: Thu May 10, 2018 6:42 pm
Location: Piedmont, Italy

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by glovisol » Thu Jul 11, 2019 5:57 am

Hi Phil & Paul,

1) Very many thanks for the modeling @ 7 Mhz, which is mid-band, as the antenna works fine down to 3.6 and up (best at 14 MHz). The transformer at present is 450 to 1000 Ohm. From your data, at last @ 3.6 MHz, it should be rather 200 to 1000 Ohm, but Z data up to 14 MHz should be necessary. Since noise is really low (with the transformer) the best match will surely increase antenna efficiency.

2) Best performance at 3.6 MHz is with antenn placed horizontally on the vertical metal railing you see in the photo.

3) On 7 & 14 MHz the antenna works both in a horizontal & in a vertical position l and exhibits some limited directivity. Limited probably because the narrow space on the balcony does not allow me to neatly manipulate it.

4) Yesterday evening I contated my supplier who is now sending me a few ferrite toroids & copper wire, so I shall be able to build suitable transformers, which seem the most critical part of the antenna.

5) The precision measurement of one side of the square (dictated by the salvaged planks) length is 88 cm.

Kind regards,

Gianfranco

Reason: No reason

vk7jj
Posts: 206
Joined: Thu Mar 02, 2017 9:56 am
Location: Tasmania

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by vk7jj » Thu Jul 11, 2019 11:40 am

The modelling only takes a few moments, glad to help, here is 80 and 20m
80m.png
80m.png (128.98 KiB) Viewed 1545 times
20m.png
20m.png (133.59 KiB) Viewed 1545 times
80-20.png
80-20.png (39.26 KiB) Viewed 1545 times
If you can find some zip cord or make a simple twisted pair feed from antenna wire or better still find some old TV ribbon, before you get the ferrites, it would be a waste to try to fine tune the ferrite with the coax feed. It looks like coax.

Phil

Reason: No reason

glovisol
Posts: 662
Joined: Thu May 10, 2018 6:42 pm
Location: Piedmont, Italy

Re: LW-MW-SW Relay Tuned 15' Noise Reducing Vertical Antenna

Post by glovisol » Thu Jul 11, 2019 3:18 pm

Phil,

It is not coax at all, it is a short section of electrical twin wire, like zip cord. I wish I had coax here, I have nothing!!

Thank you for your calcs. The picture I see is quite simple:
Antenna loop calc.png
Antenna loop calc.png (11.26 KiB) Viewed 1518 times
Attachments
Studying VLF underwater propagation....jpg
Studying VLF underwater propagation....jpg (138.17 KiB) Viewed 1518 times
Last edited by glovisol on Sun Jul 21, 2019 3:51 pm, edited 3 times in total.

Post Reply